Recently bought 2001 A4 question on fuel economy
#22
#23
Sigh. So much fail.
While you *do* make a compelling argument (sarcasm), Bosch agrees with me.
"Do NOT solder wires. Soldering wires will lead to early sensor failure."
http://www.boschautoparts.com/Techni...allGDWEB09.pdf
As for the brittleness, you'll have to test that on your own.
While you *do* make a compelling argument (sarcasm), Bosch agrees with me.
"Do NOT solder wires. Soldering wires will lead to early sensor failure."
http://www.boschautoparts.com/Techni...allGDWEB09.pdf
As for the brittleness, you'll have to test that on your own.
Last edited by 4Driver4; 04-01-2010 at 07:22 PM.
#24
Bosch's smartlink connector is pretty nice, but i'd guess they have other reasons for saying don't solder it, such as people who don't follow directions and would try and solder it an inch from the sensor. Electronics solder is used all over for wiring and such and it makes an excellent connection, but just because Bosch doesn't recommend it doesn't mean there is anything wrong with it. There is no reason it would hurt the sensor unless you managed to overheat it doing a poor soldering job.
#25
Back to the OP's question. A universal sensor will work just fine. We actually carry a very nifty Bosch arrangement that provides everything you need to replace your O2 with a universal sensor. There is something to be said for direct fit though, as I did O2's in my car and it took, literally, 5 minutes with the exact sensor, but it cost 60% more.
Tips:
1) Use neverseize on the new O2's threads in case you have to remove it again.
2) Also, a specialty 02 wrench makes this job very easy (and the tool can be used on other vehicles).
We carry the universal system, which a little bit better details and pricing can be found here, click click.
Tips:
1) Use neverseize on the new O2's threads in case you have to remove it again.
2) Also, a specialty 02 wrench makes this job very easy (and the tool can be used on other vehicles).
We carry the universal system, which a little bit better details and pricing can be found here, click click.
__________________
:: www.ECStuning.com :: Now with EXTENDED Customer Service hours!! | FIND US ON FACEBOOK!!
Phone: 1.800.924.5172 - Sales: 8:30am to MIDNIGHT EST | Customer Service 8:30am - 8pm EST
Questions? PM us for a quick response! | Email: Pete@ecstuning.com
:: www.ECStuning.com :: Now with EXTENDED Customer Service hours!! | FIND US ON FACEBOOK!!
Phone: 1.800.924.5172 - Sales: 8:30am to MIDNIGHT EST | Customer Service 8:30am - 8pm EST
Questions? PM us for a quick response! | Email: Pete@ecstuning.com
#26
Audiworld Junior Member
Thread Starter
Join Date: Mar 2010
Posts: 16
Likes: 0
Received 0 Likes
on
0 Posts
Back to the OP's question. A universal sensor will work just fine. We actually carry a very nifty Bosch arrangement that provides everything you need to replace your O2 with a universal sensor. There is something to be said for direct fit though, as I did O2's in my car and it took, literally, 5 minutes with the exact sensor, but it cost 60% more.
Tips:
1) Use neverseize on the new O2's threads in case you have to remove it again.
2) Also, a specialty 02 wrench makes this job very easy (and the tool can be used on other vehicles).
We carry the universal system, which a little bit better details and pricing can be found here, click click.
Tips:
1) Use neverseize on the new O2's threads in case you have to remove it again.
2) Also, a specialty 02 wrench makes this job very easy (and the tool can be used on other vehicles).
We carry the universal system, which a little bit better details and pricing can be found here, click click.
#27
^^ One is OEM and one is Bosch.
__________________
:: www.ECStuning.com :: Now with EXTENDED Customer Service hours!! | FIND US ON FACEBOOK!!
Phone: 1.800.924.5172 - Sales: 8:30am to MIDNIGHT EST | Customer Service 8:30am - 8pm EST
Questions? PM us for a quick response! | Email: Pete@ecstuning.com
:: www.ECStuning.com :: Now with EXTENDED Customer Service hours!! | FIND US ON FACEBOOK!!
Phone: 1.800.924.5172 - Sales: 8:30am to MIDNIGHT EST | Customer Service 8:30am - 8pm EST
Questions? PM us for a quick response! | Email: Pete@ecstuning.com
#28
Sigh. So much fail.
While you *do* make a compelling argument (sarcasm), Bosch agrees with me.
"Do NOT solder wires. Soldering wires will lead to early sensor failure."
http://www.boschautoparts.com/Techni...allGDWEB09.pdf
As for the brittleness, you'll have to test that on your own.
While you *do* make a compelling argument (sarcasm), Bosch agrees with me.
"Do NOT solder wires. Soldering wires will lead to early sensor failure."
http://www.boschautoparts.com/Techni...allGDWEB09.pdf
As for the brittleness, you'll have to test that on your own.
I am an electrical engineer and have worked for DoD contractors. Guess what? The preferred method of electrical connection is solder, not crimp. A proper solder job will last longer and have lower resistance than a crimp job. Is that compelling enough, or do I need a link to a PDF?
#29
Not to kill the debate going on here, but we also carry direct fit (non solder/crimping) sensors. In fact, they are 53% OFF right now, just get one and keep it easy!
Click here for direct replacement O2 Sensors
Click here for direct replacement O2 Sensors
__________________
:: www.ECStuning.com :: Now with EXTENDED Customer Service hours!! | FIND US ON FACEBOOK!!
Phone: 1.800.924.5172 - Sales: 8:30am to MIDNIGHT EST | Customer Service 8:30am - 8pm EST
Questions? PM us for a quick response! | Email: Pete@ecstuning.com
:: www.ECStuning.com :: Now with EXTENDED Customer Service hours!! | FIND US ON FACEBOOK!!
Phone: 1.800.924.5172 - Sales: 8:30am to MIDNIGHT EST | Customer Service 8:30am - 8pm EST
Questions? PM us for a quick response! | Email: Pete@ecstuning.com
#30
I am an electrical engineer and have worked for DoD contractors. Guess what? The preferred method of electrical connection is solder, not crimp. A proper solder job will last longer and have lower resistance than a crimp job. Is that compelling enough, or do I need a link to a PDF?
I agree that solder makes a better mechanical connection. However, Bosch, the manufacturer of the device, does not recommend it. I've heard different reasons for this, including possible damage to the sensor from flux damage. Regardless of the logic or science, the manufacturer does not recommend solder and has provided an excellent alternative.
Get back in the box, engineer! LOL