Revo Software tuning dyno results on a MAHA 217HP & 215 ft/lb's torque
04-28-2004, 06:58 PM
#135
New Member
Join Date: Mar 2004
Posts: 250
Likes: 0
Received 0 Likes
on
0 Posts
Internet marketing with blank pages is very unprofessional.
take it from me, I work for one of the largest internet marketing firms in the USA. Blank pages lead people to jump to conlusions. You should take the 10 minutes to write the content, or just take the pages down, simple as that.
If you are telling us that fabing 10 intercoolers makes you so busy, why are you wasting time to slander one of your competitors?
If you are telling us that fabing 10 intercoolers makes you so busy, why are you wasting time to slander one of your competitors?
04-28-2004, 07:22 PM
#136
AudiWorld Super User
Join Date: Jun 2000
Posts: 5,949
Likes: 0
Received 0 Likes
on
0 Posts
Slander?
I asked a question like anyone else on this site can do. It was actually a compliment about him dyno testing.
I don't have to "take it from you" and don't care who you work for. NOTHING is more important than completing orders, I could care less right now about a website.
BTW: The temp in LA just fell off a cliff, you should go back to AMS tomorrow.
I don't have to "take it from you" and don't care who you work for. NOTHING is more important than completing orders, I could care less right now about a website.
BTW: The temp in LA just fell off a cliff, you should go back to AMS tomorrow.
04-28-2004, 10:17 PM
#139
AudiWorld Super User
Join Date: Jun 2001
Posts: 8,952
Likes: 0
Received 0 Likes
on
0 Posts
Yeah, with temps like this any extra IC will shine. It's the summer that counts. :)
You ever fabbed any dual or single SMIC's for the A4 (as heretical as that may sound to some but then I am a heretic)? If that pic was your work I noted some nice little tipoffs on paying attention to detail.
I agree on the need to get before/after test runs. Publish, interpret, correct, retest. It's a constant battle.
I agree on the need to get before/after test runs. Publish, interpret, correct, retest. It's a constant battle.
04-28-2004, 10:24 PM
#140
Former Vendor
Thread Starter
Join Date: Jun 2003
Posts: 1,789
Likes: 0
Received 0 Likes
on
0 Posts
Re: Neuspeed software w Dual IC's vs. Revo with stock single side mount comparison...
Greg (Neuspeed)
At EuroCode Tuning we have a mission to have any of our signature products that claim a gain in performance on a vehicle verified by a third party unlike some of our competitors. In this quest we chose Advanced Motorsport Solution (AMS) because they do not have any Interest in our company and in fact they are direct competitors of Revo Technik America in the V.W. & Audi chip tuning industry. AMS also houses a MAHA dynamometer which is very highly regarded by V.W. & Audi so much so that they have listed it with a factory tool number and you can purchase it directly from them if you so wish. We felt this would be a good starting point and made the decision to take our vehicle there. This would leave no doubt regarding the legitimacy of these numbers in any of our customer's minds and also to prevent any of our direct competitors to question the performance of the product we sell or our company's integrity.
The fact that any company would accuse EuroCode Tuning of manipulating the dyno by increasing the sampling rate to make the dyno graph jump around or to make it look incredibly smooth when in fact we never had our hands on the dyno at any point is a flat out lie and slander. Unless, there is factual evidence to back up these accusations we demand that an apology be extended immediately. If a response is not received we will treat such accusations as simple slander.
Sincerly,
David Sarabi<ul><li><a href="https://forums.audiworld.com/a4gen2/msgs/589440.phtml">https://forums.audiworld.com/a4gen2/msgs/589440.phtml</a</li></ul>
At EuroCode Tuning we have a mission to have any of our signature products that claim a gain in performance on a vehicle verified by a third party unlike some of our competitors. In this quest we chose Advanced Motorsport Solution (AMS) because they do not have any Interest in our company and in fact they are direct competitors of Revo Technik America in the V.W. & Audi chip tuning industry. AMS also houses a MAHA dynamometer which is very highly regarded by V.W. & Audi so much so that they have listed it with a factory tool number and you can purchase it directly from them if you so wish. We felt this would be a good starting point and made the decision to take our vehicle there. This would leave no doubt regarding the legitimacy of these numbers in any of our customer's minds and also to prevent any of our direct competitors to question the performance of the product we sell or our company's integrity.
The fact that any company would accuse EuroCode Tuning of manipulating the dyno by increasing the sampling rate to make the dyno graph jump around or to make it look incredibly smooth when in fact we never had our hands on the dyno at any point is a flat out lie and slander. Unless, there is factual evidence to back up these accusations we demand that an apology be extended immediately. If a response is not received we will treat such accusations as simple slander.
Sincerly,
David Sarabi<ul><li><a href="https://forums.audiworld.com/a4gen2/msgs/589440.phtml">https://forums.audiworld.com/a4gen2/msgs/589440.phtml</a</li></ul>