Q5 Lane Change Assist fault
#12
![Default](https://www.audiworld.com/forums/images/icons/icon1.gif)
Good afternoon Guys,
So got the Lane Assist error and couldn't turn it back on. I see this thread and wonder if anyone has any advice?
Thanks
1 Fault Found:
730117 - Control Module 2 for Lane-Change Assist
C1115 F0 [009] - Automatic Calibration Not Possible
Confirmed - Tested Since Memory Clear
So got the Lane Assist error and couldn't turn it back on. I see this thread and wonder if anyone has any advice?
Thanks
1 Fault Found:
730117 - Control Module 2 for Lane-Change Assist
C1115 F0 [009] - Automatic Calibration Not Possible
Confirmed - Tested Since Memory Clear
#13
![Default](https://www.audiworld.com/forums/images/icons/icon1.gif)
I did climb under the car and check for any water/corrosion and didn't see anything. Do you all know if there is a way to troubleshoot this? It looks like you can buy used sensors off ebay but don't know if it is a sensor or something else. I am trying to avoid a trip to Audi for a $$$$ fix. I have a VCDS if that helps.
Thanks
Thanks
#14
![Default](https://www.audiworld.com/forums/images/icons/icon1.gif)
Also here is the full fault. So hopefully you all can decifer. But it seems like since it is the "SLAVE" unit means passenger side from attached pdf. Thanks for any light you all can share.
Address 3C: Lane Change (J769) Labels:| 5Q0-907-566.clb
Part No SW: 8T0 907 566 B HW: 8T0 907 566 B
Component: SWA Master H05 0071
Serial number: 0335713137
Coding: 010211
Shop #: WSC 06334 000 00000
ASAM Dataset: EV_LaneChangAssis 001020
ROD: EV_LaneChangAssis_AU21.rod
VCID: 3FDB424B27F35E03B69-806B
Lane change assistance control module 2:
Subsystem 1 - Part No SW: 8T0 907 568 B HW: 8T0 907 568 B
Component: SWA Slave H05 0071
Serial number: 0335135384
Coding: 010211
1 Fault Found:
730117 - Control Module 2 for Lane-Change Assist
C1115 F0 [009] - Automatic Calibration Not Possible
Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 3
Fault Frequency: 1
Reset counter: 166
Mileage: 158046 km
Date: 2021.06.30
Time: 11:32:48
Address 3C: Lane Change (J769) Labels:| 5Q0-907-566.clb
Part No SW: 8T0 907 566 B HW: 8T0 907 566 B
Component: SWA Master H05 0071
Serial number: 0335713137
Coding: 010211
Shop #: WSC 06334 000 00000
ASAM Dataset: EV_LaneChangAssis 001020
ROD: EV_LaneChangAssis_AU21.rod
VCID: 3FDB424B27F35E03B69-806B
Lane change assistance control module 2:
Subsystem 1 - Part No SW: 8T0 907 568 B HW: 8T0 907 568 B
Component: SWA Slave H05 0071
Serial number: 0335135384
Coding: 010211
1 Fault Found:
730117 - Control Module 2 for Lane-Change Assist
C1115 F0 [009] - Automatic Calibration Not Possible
Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 3
Fault Frequency: 1
Reset counter: 166
Mileage: 158046 km
Date: 2021.06.30
Time: 11:32:48
#16
#17
AudiWorld Senior Member
![Default](https://www.audiworld.com/forums/images/icons/icon1.gif)
Anyone find a solution to this? Got the same error “control module 2 for lane-change assist” “automatic calibration not possible”. No accidents or damage to the bumper recently (that I am aware of)
#19
AudiWorld Senior Member
![Default](https://www.audiworld.com/forums/images/icons/icon1.gif)
Thanks Dennis. I tried clearing it with VCDS and it came back immediately as soon as I turned it on (the warning disables it until you turn it back on) and drove above 40 mph. When I’m home I will look in VCDS as I saw you can check the angular deviations, it’s only the one on the passenger side rear bumper that says it can’t calibrate.