S line Heated and Illuminated Shift Knob Installed - *Warning: Once you go heated you won't go back*
#1
S line Heated and Illuminated Shift **** Installed - *Warning: Once you go heated you won't go back*
A heated shift **** is the best thing going, within 10 min of turning it on its nice a warm making winter gloveless driving a blast. The LEDS match nicely and I wired the heater into the drivers side control switch. So the temperature is regulated off the switch. I have a diagram if anyone needs it) I'll keep the pictures to a minimum but if anyone needs any help with anything let me know. Ok, Who's next?
<b>Enlarging the Shift **** Center Hole</b>
<img src="http://www.rpi.edu/~onksej/Audi%20Stuff/Shift%20Knob/install1.JPG">
<b>Feed the Wires Through Here</b>
<img src="http://www.rpi.edu/~onksej/Audi%20Stuff/Shift%20Knob/install2.JPG">
<b>LED & Heater Wired In </b>
<img src="http://www.rpi.edu/~onksej/Audi%20Stuff/Shift%20Knob/install3.JPG">
<b> Installed </b>
<img src="http://www.rpi.edu/~onksej/Audi%20Stuff/Shift%20Knob/install4.JPG">
<b>Night Shot (Perfect Match)</b>
<img src="http://www.rpi.edu/~onksej/Audi%20Stuff/Shift%20Knob/install5.JPG">
<b>Enlarging the Shift **** Center Hole</b>
<img src="http://www.rpi.edu/~onksej/Audi%20Stuff/Shift%20Knob/install1.JPG">
<b>Feed the Wires Through Here</b>
<img src="http://www.rpi.edu/~onksej/Audi%20Stuff/Shift%20Knob/install2.JPG">
<b>LED & Heater Wired In </b>
<img src="http://www.rpi.edu/~onksej/Audi%20Stuff/Shift%20Knob/install3.JPG">
<b> Installed </b>
<img src="http://www.rpi.edu/~onksej/Audi%20Stuff/Shift%20Knob/install4.JPG">
<b>Night Shot (Perfect Match)</b>
<img src="http://www.rpi.edu/~onksej/Audi%20Stuff/Shift%20Knob/install5.JPG">
#7
Questions:
1. What did you use for the heater (PN, source, and cost?)
2. What is supplying power to the heater? I guess I would like the wiring diagram.
3. What do you charge for machining services on my Raffi **** (need the top bored out)...
2. What is supplying power to the heater? I guess I would like the wiring diagram.
3. What do you charge for machining services on my Raffi **** (need the top bored out)...
Trending Topics
#10
Answers
<center><img src="http://www.rpi.edu/~onksej/Audi%20Stuff/Shift%20Knob/Diagram.JPG"></center><p>1. This will depend on several things, weight, material, thickness and voltage. For S line I would recommend around 5W and thing less will take to long to heat anything much more will burn you. You need a Silicon Rubber Foil Heater with PSA. I would recommend calculating the heat loss before buying. I have a Maple program if you need it.
2. Pic Attached (My best hand writing) Wire your heater into #2
3. I can do it but I can't get to the lathe till mid-Jan. My little apartment one I don't think a Raffi **** will fit into it.<ul><li><a href="http://www.minco.com">Answer to #1</a></li></ul>
2. Pic Attached (My best hand writing) Wire your heater into #2
3. I can do it but I can't get to the lathe till mid-Jan. My little apartment one I don't think a Raffi **** will fit into it.<ul><li><a href="http://www.minco.com">Answer to #1</a></li></ul>